dt-bindings: power: supply: bq25890: Convert to DT schema format
Convert the binding to DT schema format. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Rob Herring <robh@kernel.org>
This commit is contained in:
committed by
Sebastian Reichel
parent
ce49e42822
commit
648d383253
@@ -1,60 +0,0 @@
|
||||
Binding for TI bq25890 Li-Ion Charger
|
||||
|
||||
This driver will support the bq25892, the bq25896 and the bq25890. There are
|
||||
other ICs in the same family but those have not been tested.
|
||||
|
||||
Required properties:
|
||||
- compatible: Should contain one of the following:
|
||||
* "ti,bq25890"
|
||||
* "ti,bq25892"
|
||||
* "ti,bq25895"
|
||||
* "ti,bq25896"
|
||||
- reg: integer, i2c address of the device.
|
||||
- interrupts: interrupt line;
|
||||
- ti,battery-regulation-voltage: integer, maximum charging voltage (in uV);
|
||||
- ti,charge-current: integer, maximum charging current (in uA);
|
||||
- ti,termination-current: integer, charge will be terminated when current in
|
||||
constant-voltage phase drops below this value (in uA);
|
||||
- ti,precharge-current: integer, maximum charge current during precharge
|
||||
phase (in uA);
|
||||
- ti,minimum-sys-voltage: integer, when battery is charging and it is below
|
||||
minimum system voltage, the system will be regulated above
|
||||
minimum-sys-voltage setting (in uV);
|
||||
- ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV);
|
||||
- ti,boost-max-current: integer, maximum allowed current draw in boost mode
|
||||
(in uA).
|
||||
|
||||
Optional properties:
|
||||
- ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz,
|
||||
otherwise 1.5MHz;
|
||||
- ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the
|
||||
input current will be the lower between the resistor setting and the IINLIM
|
||||
register setting;
|
||||
- ti,thermal-regulation-threshold: integer, temperature above which the charge
|
||||
current is lowered, to avoid overheating (in degrees Celsius). If omitted,
|
||||
the default setting will be used (120 degrees);
|
||||
- ti,ibatcomp-micro-ohms: integer, value of a resistor in series with
|
||||
the battery;
|
||||
- ti,ibatcomp-clamp-microvolt: integer, maximum charging voltage adjustment due
|
||||
to expected voltage drop on in-series resistor;
|
||||
|
||||
Example:
|
||||
|
||||
bq25890 {
|
||||
compatible = "ti,bq25890";
|
||||
reg = <0x6a>;
|
||||
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
|
||||
|
||||
ti,battery-regulation-voltage = <4200000>;
|
||||
ti,charge-current = <1000000>;
|
||||
ti,termination-current = <50000>;
|
||||
ti,precharge-current = <128000>;
|
||||
ti,minimum-sys-voltage = <3600000>;
|
||||
ti,boost-voltage = <5000000>;
|
||||
ti,boost-max-current = <1000000>;
|
||||
|
||||
ti,use-ilim-pin;
|
||||
ti,thermal-regulation-threshold = <120>;
|
||||
};
|
||||
@@ -0,0 +1,123 @@
|
||||
# SPDX-License-Identifier: GPL-2.0
|
||||
# Copyright (C) 2021 Sebastian Reichel
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: "http://devicetree.org/schemas/power/supply/bq25890.yaml#"
|
||||
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
|
||||
|
||||
title: Binding for bq25890, bq25892, bq25895 and bq25896 Li-Ion Charger
|
||||
|
||||
maintainers:
|
||||
- Sebastian Reichel <sre@kernel.org>
|
||||
|
||||
allOf:
|
||||
- $ref: power-supply.yaml#
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
enum:
|
||||
- ti,bq25890
|
||||
- ti,bq25892
|
||||
- ti,bq25895
|
||||
- ti,bq25896
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
interrupts:
|
||||
maxItems: 1
|
||||
|
||||
ti,battery-regulation-voltage:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: maximum charging voltage (in uV)
|
||||
|
||||
ti,charge-current:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: maximum charging current (in uA)
|
||||
|
||||
ti,termination-current:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: |
|
||||
charge will be terminated when current in constant-voltage phase
|
||||
drops below this value (in uA)
|
||||
|
||||
ti,precharge-current:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: maximum charge current during precharge phase (in uA)
|
||||
|
||||
ti,minimum-sys-voltage:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: |
|
||||
when battery is charging and it is below minimum system voltage,
|
||||
the system will be regulated above minimum-sys-voltage setting (in uV)
|
||||
|
||||
ti,boost-voltage:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: VBUS voltage level in boost mode (in uV)
|
||||
|
||||
ti,boost-max-current:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: maximum allowed current draw in boost mode (in uA)
|
||||
|
||||
ti,boost-low-freq:
|
||||
description: boost mode frequency will be 500kHz, otherwise 1.5MHz
|
||||
type: boolean
|
||||
|
||||
ti,use-ilim-pin:
|
||||
description: |
|
||||
ILIM resistor will be used and the input current will be the lower
|
||||
between the resistor setting and the IINLIM register setting
|
||||
type: boolean
|
||||
|
||||
ti,thermal-regulation-threshold:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: |
|
||||
temperature above which the charge current is lowered, to avoid overheating
|
||||
(in degrees Celsius). If omitted, the default setting will be used (120 degrees)
|
||||
|
||||
ti,ibatcomp-micro-ohms:
|
||||
description: value of a resistor in series with the battery (in Micro Ohms)
|
||||
|
||||
ti,ibatcomp-clamp-microvolt:
|
||||
description: max. charging voltage adjustment due to expected voltage drop on in-series resistor
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- reg
|
||||
- interrupts
|
||||
- ti,battery-regulation-voltage
|
||||
- ti,charge-current
|
||||
- ti,termination-current
|
||||
- ti,precharge-current
|
||||
- ti,minimum-sys-voltage
|
||||
- ti,boost-voltage
|
||||
- ti,boost-max-current
|
||||
|
||||
additionalProperties: false
|
||||
|
||||
examples:
|
||||
- |
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
i2c0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
charger@6a {
|
||||
compatible = "ti,bq25890";
|
||||
reg = <0x6a>;
|
||||
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
|
||||
|
||||
ti,battery-regulation-voltage = <4200000>;
|
||||
ti,charge-current = <1000000>;
|
||||
ti,termination-current = <50000>;
|
||||
ti,precharge-current = <128000>;
|
||||
ti,minimum-sys-voltage = <3600000>;
|
||||
ti,boost-voltage = <5000000>;
|
||||
ti,boost-max-current = <1000000>;
|
||||
|
||||
ti,use-ilim-pin;
|
||||
ti,thermal-regulation-threshold = <120>;
|
||||
};
|
||||
};
|
||||
Reference in New Issue
Block a user