The AD5770R is a 6-channel, 14-bit resolution, low noise, programmable
current output digital-to-analog converter (DAC) for photonics control
applications.
It contains five 14-bit resolution current sourcing DAC channels and one
14-bit resolution current sourcing/sinking DAC channel.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The look-up-table for currens to lux is simply specifying
all currents from 5..47 mA, if we add some values for 0..5
we can just select the index for the lux value in an array
from the mA value. Use clamp() to get the value in the
range of values in the array.
Cc: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Gregor Riepl <onitake@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Atlas Scientific DO-SM OEM sensor reads disolved oxygen in
a solution. This is reported back as mg/L which maps directly
to ppm and so the IIO_CONCENTRATION channel type can be used.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sensors don't actually need a interrupt line to give valid readings,
and can triggered with CONFIG_IIO_HRTIMER_TRIGGER as well. Remove
the required check for interrupt, and continue along in the probe
function.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Temperature sensor works correctly only when accel and/or gyro
is turned on. Prevent polling value if they are not running.
Anyway it doesn't make sense to use it without sensor engines
on.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use runtime power management for handling chip power and
sensor engines on/off. Simplifies things a lot since pm
runtime already has reference counter.
Usage of autosuspend reduces the number of power on/off. This
makes polling interface now usable to get data at low
frequency.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sampling rate can be changed while the chip is running. It can
be useful thus do not prevent it.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When reading data with the polling interface, we need to wait
at 1 sampling period to have a sample.
For gyroscope and magnetometer, we need to wait for 2 periods
before having a correct sample.
Not suitable for stable or backporting.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rewrite clock management to use automatic clock switching
present since MPU6500.
Sensors engine management can now turn on or off a batch of
sensors which simplifies usage a lot.
Temperature sensor is now turned on/off depending on usage.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Turning vdd regulator on requires a consequent sleep for the
chip to power on correctly.
Turning vddio regulator is much faster.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Old chips using spi require for a full reset to manually reset
all signal path. This does not harm when using i2c so do it
inconditionally. Exclude i2c only chips.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Init chip_config early and use its values for initial setup.
More coherent, prevent possible mistakes.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not change the sampling rate value. Let userspace decide what
is the sampling rate to use.
Read only the requested axis.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This way there is no need anymore to export the power function to
i2c and spi modules.
Bus setup is done inside init when power is on and the result is
now checked.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If we are here it means we have fifo enabled for 1 sensor
at least. And interrupt is always required for using trigger.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c auxiliary mux is done by analog switches. You do not need to
set them for every i2c transfer.
Just set i2c bypass bit at init and do noting in i2c de/select.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Clock should be enabled as soon as using master modes, even before
enabling timer. Or, this may provoke bad behavior on the other end
(slave timer). Then, introduce 'clk_enabled' flag, instead of relying
on CR1 EN bit, to keep track of clock being enabled (balanced refcount).
Propagate this anywhere else in the driver.
Also add 'remove' routine to stop timer and disable clock in case it
has been left enabled. Enforce the user interface has been unregistered
in the remove routine, before disabling the hardware to avoid possible
race. So, remove use of devm_ variant to register triggers and unregister
them before the hardware gets disabled [1].
[1] https://patchwork.kernel.org/patch/9956247/
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- allow autoloading when build as module and defined inside DT
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_add_action_or_reset to automatically disable the device
and allow you to get rid of the remove function entirely.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AL3320a is fairly simple chip, so for suspend is enough to disable and
later enable it again.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- modified to be in part with al3010 driver
- cleanup using bitfield, no functionality change intended
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the posibility do read and write registers from userspace
using the kernel debug direct register access option.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All of the actions done in `adis16460_initial_setup()` are now done in
`__adis_initial_startup()` so, there's no need for code duplication.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All actions done in `adis16480_initial_setup()` are now done in
`__adis_initial_startup()` so, there's no need for code duplication.
Furthermore, the call to `adis16480_initial_setup()` is done before any
device configuration since the device will be reset if not already (via
rst pin). This is actually fixing a potential bug since `adis_reset()` was
being called after configuring the device which is obviously a problem.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Each driver/chip that wants to validate it's product id, can now
specify a 'prod_id_reg' and an expected 'prod_id' value.
The 'prod_id' value is intentionally left 0 (uninitialized). There aren't
(yet) any product IDs with value 0; this enforces that both 'prod_id_reg'
and 'prod_id' are specified.
At the very least, this routine validates that the SPI connection to the
ADIS chip[s] works well.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All the ADIS devices perform, at the beginning, a self test to make sure
the device is in a sane state. Previously, the logic was that the self-test
was performed in adis_initial_startup() and if that failed a reset was done
and then a self-test was attempted again.
This change unifies the reset mechanism under the adis_initial_startup()
call. A HW reset will be done if GPIO is configured, or a SW reset
otherwise. This should make sure that the chip is in a sane state for
self-test. Once the reset is done, the self-test operation will be
performed. If anything goes wrong with self-test, the driver should just
bail/error-out (i.e. no second attempt). The chip would likely not be a in
a sane state state if the self-test fails after a reset.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a dedicated self_test_reg variable. This is also a step
to let new drivers make use of `adis_initial_startup()`. Some devices
use MSG_CTRL reg to request a self_test command while others use the
GLOB_CMD register.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change splits the __adis_initial_startup() away from
adis_initial_startup(). The unlocked version can be used in certain calls
during probe, where races won't happen since the ADIS driver may not be
registered yet with IIO.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change overrides commit 380b107bbf ("iio: adis: Introduce timeouts
structure"). It removes the memory allocation and moves the 'adis_data'
information to be static on the chip_info struct.
This also adds a timeout structure to ADIS16334, since it was initially
omitted. This was omitted (by accident) when the change was done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change overrides commit 380b107bbf ("iio: adis: Introduce timeouts
structure"). It removes the memory allocation and moves the 'adis_data'
information to be static on the chip_info struct.
This also adds a timeout structure to ADIS16334, since it was initially
omitted. This was omitted (by accident) when the change was done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change overrides commit 380b107bbf ("iio: adis: Introduce timeouts
structure"). It removes the memory allocation and moves the 'adis_data'
information to be static on the chip_info struct.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing return value check in st_lsm6dsx_shub_read_oneshot disabling
the slave device connected to the st_lsm6dsx i2c controller.
The issue is reported by coverity with the following error:
Unchecked return value:
If the function returns an error value, the error value may be mistaken
for a normal value.
Addresses-Coverity-ID: 1456767 ("Unchecked return value")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
SPS30 uses triggered buffer, but the dependency is not specified in the
Kconfig file. Fix this by selecting IIO_BUFFER and IIO_TRIGGERED_BUFFER
config symbols.
Cc: stable@vger.kernel.org
Fixes: 232e0f6dde ("iio: chemical: add support for Sensirion SPS30 sensor")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Vishay has published a new version of "Designing the VCNL4200 Into an
Application" application note in October 2019. The new version specifies
that there is +-20% of part to part tolerance. Although the application
note is related to vcnl4200, according to support the vcnl4040's "ASIC
is quite similar to that one for the VCNL4200".
So update the sampling periods (and comment), including the correct
sampling period for proximity. Both sampling periods are lower. Users
relying on the blocking behaviour of reading will get proximity
measurements much earlier.
Fixes: 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Vishay has published a new version of "Designing the VCNL4200 Into an
Application" application note in October 2019. The new version specifies
that there is +-20% of part to part tolerance. This explains the drift
seen during experiments. The proximity pulse width is also changed from
32us to 30us. According to the support, the tolerance also applies to
ambient light.
So update the sampling periods. As the reading is blocking, current
users may notice slightly longer response time.
Fixes: be38866fbb ("iio: vcnl4000: add support for VCNL4200")
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
At the moment, reading from in_magn_*_raw in sysfs tends to return
large values around 65000, even though the output of ak8974 is actually
limited to ±32768. This happens because the value is never converted
to the signed 16-bit integer variant.
Add an explicit cast to s16 to fix this.
Fixes: 7c94a8b2ee ("iio: magn: add a driver for AK8974")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Waleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Master mode should be disabled when stopping. This mainly impacts
possible other use-case after timer has been stopped. Currently,
master mode remains set (from start routine).
Fixes: 6fb34812c2 ("iio: stm32 trigger: Add support for TRGO2 triggers")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As every chip has some little variant in LPF bandwidth values,
use common values that are working for all chips.
Simplify the LPF setting function.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Tachici